Page 5 of 7
Re: NO2C and Speeduino Boards and Components For Sale From USA
Posted: Fri Feb 09, 2018 5:26 pm
by Robert T Lewis
I have a boxer engine ,Ural ,a twin with a wasted spark ignition , It right now has an inductive crank sensor. it
It was setup for fuel injection , but I want to run carbs so I will only be using he ignition section, I assume even if I totally populate the entire board I can only use the ignition .
How do I buy a board and component kit?
I am in Illinois
Re: NO2C and Speeduino Boards and Components For Sale From USA
Posted: Fri Feb 09, 2018 7:22 pm
by Ceeloo Yello
If you look at the 1st post you can either PM him or send him an email via his gmail, he accepts paypal.
Re: NO2C and Speeduino Boards and Components For Sale From USA
Posted: Fri Feb 09, 2018 7:25 pm
by turboedge
Thanks, CY.
Bob, I sent you an email.
Weaver
Re: NO2C and Speeduino Boards and Components For Sale From USA
Posted: Tue Feb 13, 2018 8:08 pm
by Djwind
@turbo - Do you have a website setup for the sales stuff yet?
Re: NO2C and Speeduino Boards and Components For Sale From USA
Posted: Tue Feb 13, 2018 10:12 pm
by turboedge
Hi DjWind,
There is a website,
http://WTMtronics.com, but it is not ready yet. It needs to be though, and I have been on a get s--t done spree lately (thanks Dwight). My last project, an NO2C case, is pretty well done. I'm sure someone well versed in 3D CAD could have done better, but it works. Dwight will be using a couple of them soon. I think my next project should be to get the website functioning properly.
Thanks, Weaver
Re: NO2C and Speeduino Boards and Components For Sale From USA
Posted: Tue Feb 27, 2018 4:40 pm
by ewwgoblins
Are you still selling the V4 boards? I would like to purchase one!
Re: NO2C and Speeduino Boards and Components For Sale From USA
Posted: Tue Feb 27, 2018 4:52 pm
by turboedge
Yes!
Send me an email with your info.
turboedge@wtmtronics.com
Thanks! Weaver
Re: NO2C and Speeduino Boards and Components For Sale From USA
Posted: Thu Apr 12, 2018 2:09 pm
by turboedge
Hey guys,
It's not much, but the website
WTMtronics.com has been proven to function.
Thanks Edward for being the first official customer!
Weaver
Re: NO2C and Speeduino Boards and Components For Sale From USA
Posted: Sat Apr 14, 2018 4:18 am
by clockman48
Hi
Happy to be first customer.
been watching your NO2C. was going with official V0.4.4, but wanted to keep it smaller for motor scooter use. wanted to do my own pcb but Fritzing is a project of its own. I like working with Honda cn250 Helix, and converting to "chopper". newest project is converting motor to EFI....hence interest in speeduino.
Looking now for a schematic for your NO2C. may have missed it and now will review all your posts.
Good luck with the site.
Edward
Re: NO2C and Speeduino Boards and Components For Sale From USA
Posted: Fri Jun 01, 2018 9:41 pm
by turboedge
Hey Peeps, I now have dual channel signal conditioners available for $19.95 (shipped free worldwide) on my web-page
https://wtmtronics.com.
Also Edward and anyone else that is looking, the quest for information about the NO2C starts on the wiki in the section called third party boards
https://speeduino.com/wiki/index.php/3rd_party
And finally a sneak-peak of the UA4C vA1 Seawolf, which should be available before summer is over in the US. Case shown is 120x103x31mm.