For any add-on boards such as VR conditioners, optos and OEM interface boards
#65106
dener0987 wrote: Mon Oct 02, 2023 1:09 pm I didn't get to test it with an oscilloscope. I was just basing it off the megasquirt grounding scheme.
Well the MS scheme tallies with the Bosch recommendation. It may well cause issues - the application information for the CJ125 separates the power and signal ground, this was a change from the CJ110 application example where they were shown as common which did cause issues. The SPI interface was a further change to eliminate ground issues.
#65550
Hi,

got a question about the PWM output pin Voltage of the bl49sp

i'd like to have a narrowband 0-1V output signal on this pin, so i can feed a OEM ecu with this signal.
how can i change this from the 0-5V signal to narrowband signal 0-1V ?

does it need adjustment on these values? :

/* Lambda Outputs are defined as follow:
*
* 0.5V = 0,68 Lambda = 10 AFR (Gasoline)
* 4,5V = 1,36 Lambda = 20 AFR (Gasoline)
*
* Internal Lambda is used in a range from 68..136
*
**/
#define LambdaToVoltage(a) ((a * 5882UL / 100UL) - 3500UL)
#define VoltageTo8BitDac(a) (a * 255UL / 5000UL)
#define VoltageTo12BitDac(a) (a * 4095UL / 5000UL)

/* Calculate millivolt from adc */
#define AdcToVoltage(a) (a * 5000UL / 1023UL)

I guess it should become something like ?:

0V = 0,68 Lambda = 10 AFR (Gasoline)
1V = 1,36 Lambda = 20 AFR (Gasoline)

im looking for hours... but unfortunately can't find my answer.

btw. im using it as standalone device, so i would like to have the 0-5V signal and one 0-1V narrowband signal to feed the OEM ecu.

can someone hep me in the right direction?
thanks.
#66683
Guys taking a deeper look at the heater PID and the FastPid library used in this project. I noticed that the setpoint and feedback of the PID algorithm is defined by the step function. However, looking at where the step function is called and the values ​​entered into it seem to be wrong. What would In.UR be? This input is connected to a capacitor that is connected to gnd.

As can be seen here on schematic https://github.com/oelprinz-org/BL49SP/ ... matics.pdf

ADC6, which would be the input for the UR, is connected to a capacitor and GND. Is this right? What is the logic behind this?

Image
#66686
Guys. After some time studying the code I have a better idea of ​​how it works.
I noticed that the Abl.UROpt variable is calculated in the calibration phase by reading the UR output of the cj125, which appears to be the signal from the nernst cell. Well, would this variable be the target of the PID? Since this variable is the target of the PID, shouldn't it be in the setpoint of the step function? According to the FastPID library documentation, the first variable of the step function is the setpoint.

Image
#66688
PSIG wrote: Sat Jan 13, 2024 11:41 pm Whatever notes are verified and correct would be AWESOME to include in the code as remarks for users to follow. :mrgreen:
Yes, I posted it here so we can debate whether I'm correct or not. Maybe the code developer can tell us if I'm correct. What do you think my correction makes sense?
#66689
dener0987 wrote: Sat Jan 13, 2024 10:11 pm Guys. After some time studying the code I have a better idea of ​​how it works.
I noticed that the Abl.UROpt variable is calculated in the calibration phase by reading the UR output of the cj125, which appears to be the signal from the nernst cell. Well, would this variable be the target of the PID? Since this variable is the target of the PID, shouldn't it be in the setpoint of the step function? According to the FastPID library documentation, the first variable of the step function is the setpoint.

Image
Hello,

that is done to change the „polarity“ of the pid controller.

And In.UR is correct
#69495
Maximum779 wrote: Mon Sep 16, 2024 3:03 pm Hello friends, i runned bl49sp 0.3 code on arduino board+ cj125 in soic-24 . I have problem. After heating i have error 0xffffe8ff . My cj125 marking "30481" . What problem i have?
I will use code 0.2,and its work. Code v0.3 is dont work.
  • 1
  • 27
  • 28
  • 29
  • 30
  • 31

If I am understanding correctly you want the out[…]

Indeed. So then I reverse-engineered the 3 origina[…]

... — is the ultimate goal to alter code t[…]

Project progressing. Have been addressing some wi[…]

Still can't find what you're looking for?