What I am confused about is that the teensy code should support 8x8 seeing as how the global def for a teensy is 8x8 declared in globals.h
I read your post in the thread about your teensy board
Outlining it’s limited to 9 being 6x3
I’ll have to look at git but doesn’t Pasis board run in a 6x6 sequential on just arduino bringing the total to 12 ?
Example straight from Joshes git declaring the teensy as a 8x8 capable board (stm32 capable of this as well according to globals.h)
https://github.com/noisymime/speeduino/ ... bals.h#L43
Code: Select all#elif defined(CORE_TEENSY)
#if defined(__MK64FX512__) || defined(__MK66FX1M0__)
#define CORE_TEENSY35
#define BOARD_H "board_teensy35.h"
#define SD_LOGGING //SD logging enabled by default for Teensy 3.5 as it has the slot built in
#elif defined(__IMXRT1062__)
#define CORE_TEENSY41
#define BOARD_H "board_teensy41.h"
#endif
#define INJ_CHANNELS 8
#define IGN_CHANNELS 8
#elif defined(STM32_MCU_SERIES) || defined(ARDUINO_ARCH_STM32) || defined(STM32)
#define CORE_STM32
#if defined(STM32F4) //F4 can do 8x8
#define INJ_CHANNELS 8
#define IGN_CHANNELS 8
So I guess that being said..
Went ahead and popped this into init.ino in order to allow a choice of board from tuner studio...
Code: Select all #if defined(CORE_TEENSY35)
case 32:
pinInjector1 = 9; //Output pin injector 1
pinInjector2 = 8; //Output pin injector 2
pinInjector3 = 5; //Output pin injector 3
pinInjector4 = 2; //Output pin injector 4
pinInjector5 = 12; //Output pin injector 5
pinInjector6 = 27; //Output pin injector 6
pinInjector7 = 24;
pinInjector8 = 25;
pinCoil1 = 29; //Pin for coil 1
pinCoil2 = 30; //Pin for coil 2
pinCoil3 = 31; //Pin for coil 3
pinCoil4 = 32; //Pin for coil 4
pinCoil5 = 28; //Pin for coil 5
pinCoil6 = 14; //Pin for coil 6
pinCoil7 = 39;
pinCoil8 = 22;
pinTrigger = 23; //The CAS pin
pinTrigger2 = 36; //The Cam Sensor pin
pinTPS = 16;//TPS input pin
pinMAP = 17; //MAP sensor pin
pinIAT = A11; //IAT sensor pin
pinCLT = A10; //CLS sensor pin
pinO2 = A21;
pinO2_2 = A22; //O2 Sensor pin
pinBat = 15; //Battery reference voltage pin
pinSpareHOut1 = 6;
pinSpareHOut2 = 7;
pinTachOut = 21; //Tacho output pin (Goes to ULN2003)
pinIdle1 = 10; //ICV pin1
//pinIdle2 = 6; //ICV pin3
pinBoost = 11; //Boost control
pinVVT_1 = 48; //VVT output
pinVVT_2 = 47; //Default VVT2 output
pinFuelPump = 38; //Fuel pump output (Goes to ULN2003)
pinStepperDir = 13; //Stepper valve isn't used with these
pinStepperStep = 35; //Stepper valve isn't used with these
pinFan = 37; //Pin for the fan output (Goes to ULN2003)
pinLaunch = 26; //Launch control pin
pinFlex = 49; // Flex sensor
//pinResetControl = 43; //Reset control output
break;
#endif
Then Edited the speeduino.ini file so that the offset chosen for the SCG_V1 ecu matched the actual outputs for the board...
Code: Select allI/O 0.1", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "Daz V6 Shield 0.1", "BMW PnP", "SCG_V1", "INVALID",
Code: Select all ;pinLayout = bits, U08, 15, [0:7], "Speeduino v0.1", "Speeduino v0.2", "Speeduino v0.3", "Speeduino v0.4", "INVALID", "INVALID", "01-05 MX5 PNP", "INVALID", "96-97 MX5 PNP", "NA6 MX5 PNP", "Turtana PCB", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "Plazomat I/O 0.1", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "Daz V6 Shield 0.1", "BMW PnP", "SCG_V1", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "NO2C", "UA4C", "INVALID", "INVALID", "INVALID", "DIY-EFI CORE4 v1.0", "INVALID", "INVALID", "INVALID", "INVALID", "dvjcodec Teensy RevA", "dvjcodec Teensy RevB", "INVALID", "INVALID", "INVALID", "DropBear", "INVALID", "INVALID", "INVALID", "INVALID", "Black STM32F407VET6 V0.1", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID"
defaultValue = boardFuelOutputs, 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 6 8 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 8 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4
defaultValue = boardIgnOutputs, 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 6 8 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 8 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4
Now I have testable outputs that actually match up to the boards real life outputs
the only thing I am left struggling to figure out is why I cant triger IGN1/2 from the test mode
Every other output works fine in test mode.
All in all the short answer to my inquiry is no
the board doesnt have a setup that works in speeduino
you have to create the entries yourself
The other issue I am facing I am working on figuring out still as I am sure the pins are being overridden somewhere in my choices