Help with building your Speeduino, installing it, getting it to run etc.
By subzero
#42567
Sorry for the delay have eome problems last year
Mover to 200220 firmware
Injectors are bosch 0280156023 i found is rated373 cc/minImage

You can trll me is dead time is ok .
Second question warmup .afterstart enrichments?.
Im going to fabticate this week an aluminium adapter for hall sensor and finally install all together.im going yo tune speeduino 0.3 wiyh teensy adapter .please only im a total noob about tuning.im going only to tune fuel .ezl wotk ok for me
1588324506333923093079232791353.jpg
1588324506333923093079232791353.jpg (4.96 MiB) Viewed 4873 times
15883242558306251348498172027980.jpg
15883242558306251348498172027980.jpg (5.63 MiB) Viewed 4873 times
15883242358774275026502385088871.jpg
15883242358774275026502385088871.jpg (6.53 MiB) Viewed 4873 times
IMG_20200501_114135.jpg
IMG_20200501_114135.jpg (5.67 MiB) Viewed 4873 times
By subzero
#42695
Some progress need to find tps compatibile with my mercedes tb
Finish first pary of eiting harness ground plus positives via relays and fuses
Huge ground
15888627038845435675959595725360.jpg
15888627038845435675959595725360.jpg (4.93 MiB) Viewed 4821 times
IMG_20200507_161740.jpg
IMG_20200507_161740.jpg (4.93 MiB) Viewed 4821 times
IMG_20200507_161743.jpg
IMG_20200507_161743.jpg (4.88 MiB) Viewed 4821 times
By subzero
#42719
Found box plus connector tomorrow i will start wiring
15889606435094674529694164559679.jpg
15889606435094674529694164559679.jpg (5.05 MiB) Viewed 4797 times
15889605999985590023131803518002.jpg
15889605999985590023131803518002.jpg (5.26 MiB) Viewed 4797 times
15889605910075077961955018574534.jpg
15889605910075077961955018574534.jpg (4.72 MiB) Viewed 4797 times
By subzero
#42741
IMG_20200509_213230.jpg
IMG_20200509_213230.jpg (4.46 MiB) Viewed 4754 times
IMG_20200509_213228.jpg
IMG_20200509_213228.jpg (4.12 MiB) Viewed 4754 times
IMG_20200509_213239.jpg
IMG_20200509_213239.jpg (4.35 MiB) Viewed 4754 times
IMG_20200509_213241.jpg
IMG_20200509_213241.jpg (4.28 MiB) Viewed 4754 times
Uffa box ready and fixed
By subzero
#42778
IMG_20200511_122653.jpg
IMG_20200511_122653.jpg (4.51 MiB) Viewed 4714 times
IMG_20200511_131809.jpg
IMG_20200511_131809.jpg (4.68 MiB) Viewed 4714 times
IMG_20200511_131816.jpg
IMG_20200511_131816.jpg (4.61 MiB) Viewed 4714 times
Triger wheel plus hall sensor installed
Fuelbrail adapted and ready
By subzero
#42804
IMG_20200512_155302.jpg
IMG_20200512_155302.jpg (5 MiB) Viewed 4675 times
IMG_20200512_155645.jpg
IMG_20200512_155645.jpg (4.92 MiB) Viewed 4675 times
IMG_20200512_173301.jpg
IMG_20200512_173301.jpg (5.76 MiB) Viewed 4675 times
Quasi ready need to fabricate an aluminium plate to close the extra injector hole.
Found a perfect tps small in size that fits my car
From rover car. I have to coean th wiring harness
Connect all the cables to be ok and we are ready to run and tune
By subzero
#42861
Finally found the problemm it was my teensy with adapter used an original arduino and after crank the car goes on and has rought idle need sone tuning.
A second question i use a bmw hall sensor and has 12 volt outpout ,used diode and pullup an have sync but for good sync ineed to have noise filter to medium.
,If i wire hall for 5 volts from speeduino can resolve the req filter noise i see other to have no problemm with noise or i need 10x resistor from hall to ground?
By subzero
#42891
My wideband innovate mtx l plus is stucked at 22.4 afr recalibrate and all the time is 22.4 afr is the lsu 4.9 dead or my controller
  • 1
  • 3
  • 4
  • 5
  • 6
  • 7

Hi, I am trying to assign Signed values to the x-a[…]

Vr Conditioner Noise when cranking

New version 202305 don't fix the issue. Now after[…]

blitzbox

I've finally figured out why MAP and Lambda weren'[…]

Hello, I bring news!! Let me tell you that after […]

Still can't find what you're looking for?