Page 24 of 25

Re: Speeduino + Teensy 3.5 - ECUTeen3.5 - 8INJ/8IGN/CAN - Open Source

Posted: Mon Dec 20, 2021 10:24 pm
by NickZ
don't use that pin config, some of the ignition outputs don't work on current firmware.

Re: Speeduino + Teensy 3.5 - ECUTeen3.5 - 8INJ/8IGN/CAN - Open Source

Posted: Wed Jul 27, 2022 2:02 pm
by Ironduke151
With chip shortages can person use teensy 4.1 on this board or have use 3.5 because of its 5v talent. If not have wait for new year when there available again so can built this project

Re: Speeduino + Teensy 3.5 - ECUTeen3.5 - 8INJ/8IGN/CAN - Open Source

Posted: Wed Aug 17, 2022 4:12 am
by demolishionc4
So being that its impossible to find a teensy 3.5 I figured I would try to make the stm32f407 to teensy adapter you have on github, but I was reviewing the board and I don't see any inner pins to go to the boards iat and clt, that and the pins that are addressed in the pcb file go to completely different pins

Re: Speeduino + Teensy 3.5 - ECUTeen3.5 - 8INJ/8IGN/CAN - Open Source

Posted: Wed Aug 17, 2022 7:06 am
by pazi88
Why don't you just put together STM32 based speeduino, instead of doing adapter: https://oshwlab.com/b.brazdziunas/scg-e ... _copy_copy

Re: Speeduino + Teensy 3.5 - ECUTeen3.5 - 8INJ/8IGN/CAN - Open Source

Posted: Wed Aug 17, 2022 4:43 pm
by demolishionc4
So I saw this before but I couldn't find any forums talking about it so I really didn't trust it. I guess I should of just rolled the dice and ordered some of those pcb instead

Re: Speeduino + Teensy 3.5 - ECUTeen3.5 - 8INJ/8IGN/CAN - Open Source

Posted: Thu Aug 18, 2022 6:26 am
by pazi88
demolishionc4 wrote: Wed Aug 17, 2022 4:43 pm So I saw this before but I couldn't find any forums talking about it so I really didn't trust it. I guess I should of just rolled the dice and ordered some of those pcb instead
Well I have one and has been great for testing use I have used it. I also know many that are running their car with that.

Re: Speeduino + Teensy 3.5 - ECUTeen3.5 - 8INJ/8IGN/CAN - Open Source

Posted: Mon Jul 03, 2023 11:38 am
by JDMar23
pazi88 wrote: Wed Aug 17, 2022 7:06 am Why don't you just put together STM32 based speeduino, instead of doing adapter: https://oshwlab.com/b.brazdziunas/scg-e ... _copy_copy
Which firmware its compaible with this board? And how to locate firmware for CY8C24223A without LCD? Thanks, i am newby in speeduino.

Re: Speeduino + Teensy 3.5 - ECUTeen3.5 - 8INJ/8IGN/CAN - Open Source

Posted: Mon Jul 03, 2023 12:12 pm
by dazq
JDMar23 wrote: Mon Jul 03, 2023 11:38 am
pazi88 wrote: Wed Aug 17, 2022 7:06 am Why don't you just put together STM32 based speeduino, instead of doing adapter: https://oshwlab.com/b.brazdziunas/scg-e ... _copy_copy
Which firmware its compaible with this board? And how to locate firmware for CY8C24223A without LCD? Thanks, i am newby in speeduino.
There is only one official speeduino firmware used for mega,teensy and stm32 MCU.
BUT as this board never had its pin config added to the firmware release you will need to do that yourself before uploading to the MCU.

Re: Speeduino + Teensy 3.5 - ECUTeen3.5 - 8INJ/8IGN/CAN - Open Source

Posted: Wed Jul 05, 2023 8:28 am
by JDMar23
ok, but if the board its working anyone has pin config added and firmware for CY8C24223A.

If he can share, save a lot of work.

Re: Speeduino + Teensy 3.5 - ECUTeen3.5 - 8INJ/8IGN/CAN - Open Source

Posted: Thu Jul 06, 2023 9:05 am
by JHolland
JDMar23 wrote: Wed Jul 05, 2023 8:28 am ok, but if the board its working anyone has pin config added and firmware for CY8C24223A.
If he can share, save a lot of work.
I don't think that the CY8C24223A has enough timers to run the full Speeduino firmware.