Any general discussion around the firmware, what is does, how it does it etc.
Announcements
Title Statistics Last post
Announcing SpeedyLoader!
by noisymime  - 
28 Replies 
97014 Views
by noisymime
Topics
Title Statistics Last post
7 Replies 
46956 Views
by LPG2CV
Speeduino 1990
by juliuscasey  - 
1 Replies 
66 Views
by jonbill
15 Replies 
10819 Views
by 88xj4.0
Sequential injection CAM sensor alternative.
by michaelovitch  - 
31 Replies 
16096 Views
by usatracy
Dash editing.
by valen_j  - 
4 Replies 
3399 Views
by PSIG
Adjusting VE / IGN in percent over browser
by JB21  - 
7 Replies 
702 Views
by apollard
Modifying firmware and TS .ino
by E4ODnut  - 
3 Replies 
146 Views
by PSIG
Software and harware implementation.
by Mirfak  - 
1 Replies 
198 Views
by jonbill
202310 won't compile
by E4ODnut  - 
11 Replies 
1001 Views
by jonbill
Torque reduction request for AT
by Viperjohn  - 
7 Replies 
3530 Views
by PSIG
Bmw e30 speeduino no spark
by rogelioamick  - 
1 Replies 
285 Views
by jonbill
Hello and info needed
by TurboPirate  - 
30 Replies 
34896 Views
by TurboPirate
49 Replies 
16553 Views
by PSIG
Reading sensor settings from EEPROM
by RempageR1  - 
3 Replies 
705 Views
by jonbill
STM32 development
by Tjeerd  - 
287 Replies 
355420 Views
by fuqiangjia
VE IGN Table switch via canbus STM32F407
by JB21  - 
1 Replies 
353 Views
by dazq
d17 tester needed for sequential / Vtec testing
by miker  - 
5 Replies 
7719 Views
by miker
Teensy support status
by infinityedge  - 
45 Replies 
46006 Views
by wmcdonal
Deceleration enleanment
by metcap  - 
1 Replies 
481 Views
by metcap
Problems Connecting STM32F401 Blackpill
by damichi  - 
6 Replies 
885 Views
by ptownsin
Wheel Decoder and VVT coder for Honda K series
by choyr  - 
18 Replies 
9113 Views
by nickamuch
Noob(ish) question #1...
by FoxUnpopuli  - 
2 Replies 
540 Views
by dazq
Flatshift for AT transmission
by XPbIM3  - 
24 Replies 
18644 Views
by XPbIM3
89 Replies 
45384 Views
by RowdyDouglas
Speeduino Kompressor M62
by Bartosz D  - 
2 Replies 
3148 Views
by PSIG
  • 1
  • 2
  • 3
  • 4
  • 5
  • 15
Can bus problem with STM32

I placed a 120 ohm resistor on the speeduino side […]

How bad did I mess up my PCB

It's probably recoverable. Take a look at the sche[…]

Suzuki RE-5 EFI Conversion

check the relay is clicking, and the fuse. Check t[…]

That’s awesome! Congrats! So you were still[…]

Still can't find what you're looking for?