Motronic 1.1/1.2/1.3 Compatible PCB

Re: Motronic 1.1/1.2/1.3 Compatible PCB#64417

By Raku - Tue Aug 15, 2023 2:40 am

- Tue Aug 15, 2023 2:40 am #64417

Tahitian e30 wrote: ↑Mon Aug 14, 2023 5:37 pm Hello thank you raku for sharing your knowledge
I have an e30 325i turbo and I want your v2 ecu but I'm a new to this . When I put the BOM file on the website it say it's the wrong file. How can I fix that problem? Thank you.

its not a lcsc or digikey bom file. its just for reference.

Re: Motronic 1.1/1.2/1.3 Compatible PCB#64418

By Raku - Tue Aug 15, 2023 2:44 am

- Tue Aug 15, 2023 2:44 am #64418

sk8 wrote: ↑Mon Aug 14, 2023 7:20 pm Will get a m54 cam sensor ordered. Thanks for updating the BOM.

I'm having trouble sourcing the last two parts. Seems like the IO connector(C456513) and the High Power Connector Pins(WM2501CT-ND) are not available anywhere, is there something else I can use?

added to bom

Re: Motronic 1.1/1.2/1.3 Compatible PCB#64474

By Jmami - Sat Aug 19, 2023 7:16 pm

- Sat Aug 19, 2023 7:16 pm #64474

hi @raku, not able to find Wideband O2 connectors FWF30002-D06B22K6B, MFR0W4F1200A50 anywhere can you suggest alternative sites or part numbers.

Re: Motronic 1.1/1.2/1.3 Compatible PCB#64479

By Raku - Sun Aug 20, 2023 2:55 am

- Sun Aug 20, 2023 2:55 am #64479

Jmami wrote:hi @raku, not able to find Wideband O2 connectors FWF30002-D06B22K6B, MFR0W4F1200A50 anywhere can you suggest alternative sites or part numbers.

updated bom

Re: Motronic 1.1/1.2/1.3 Compatible PCB#64501

By sk8 - Tue Aug 22, 2023 12:31 am

- Tue Aug 22, 2023 12:31 am #64501

I have most of the V2.2 board together, but not sure what jumpers I need to solder for 6cyl sequential inj, and wasted spark ign.

For stock vr crank sensor, do I need to connect anything for crank sensor power?

Screenshot 2023-08-21 at 7.24.43 PM.png (2.55 MiB) Viewed 2136 times

There's two areas here, are both for the crank sensor, or is one for the cam sensor? I will be using a hall effect cam sensor.

Screenshot 2023-08-21 at 7.25.08 PM.png (862.72 KiB) Viewed 2136 times

Also what does the SW2 area do, and what are the F1 and F2 jumper areas for?

Screenshot 2023-08-21 at 7.24.22 PM.png (1.37 MiB) Viewed 2136 times

Sorry for the dumb questions, but having a hard time figuring out the correct config here.

Re: Motronic 1.1/1.2/1.3 Compatible PCB#64502

By Raku - Tue Aug 22, 2023 2:02 am

- Tue Aug 22, 2023 2:02 am #64502

no just solder stock side jumpers.

Re: Motronic 1.1/1.2/1.3 Compatible PCB#64531

By Jmami - Wed Aug 23, 2023 5:50 am

- Wed Aug 23, 2023 5:50 am #64531

Hi @raku, can VVT input/output be added to this board. I am planning to swap 2jz gte vvti later on and thinking if we can use this same ecu for running 2jz gte vvti.

Re: Motronic 1.1/1.2/1.3 Compatible PCB#64532

By Raku - Wed Aug 23, 2023 6:31 am

- Wed Aug 23, 2023 6:31 am #64532

Can. make a MOSFET driver circuit in separate board and wire it to vvt pin on Arduino

Re: Motronic 1.1/1.2/1.3 Compatible PCB#64567

By lummpy69 - Thu Aug 24, 2023 10:44 am

- Thu Aug 24, 2023 10:44 am #64567

Hello, I would like to know why there is an exclamation mark on the first injector. Would like to use 3 of the injector outputs. Is there something to change in the tuner studio? Is for a BMW M30B35.

Mfg

Attachments

IMG_20230824_123540.jpg (2.98 MiB) Viewed 1957 times

Re: Motronic 1.1/1.2/1.3 Compatible PCB#64568

By jonbill - Thu Aug 24, 2023 11:48 am

- Thu Aug 24, 2023 11:48 am #64568

Because whoever typed it didn't notice they had the shift key pressed.