For discussion of Speeduino compatible boards designed / built by other members of the forum and for guidance around making such a board
User avatar
By jbiplane
#46648
chaoschris wrote: Sat Sep 26, 2020 7:59 pm BlitzboxBL49sp
Hi Chris & Thomas
Any news related BlitzboxBL49sp... Will this project continued or your concentrate completelly on gewitterBOX?
User avatar
By chaoschris
#46650
Hi jbiplane,
both projects will be continued. I was moving in the last weeks so there was less than no time for doing something on this.
The BlitzBox does already exist in a first testing revision of hardware, so please stay a bit patient for a while....
The focus will be on the BlitzBox because it is already playing with Tunerstudio. The GewitterBox will need much more time as there must be done a lot of work on the software side (beside the speeduino firmware).
Best regards,
Chris
User avatar
By jbiplane
#46845
chaoschris wrote:The BlitzBox does already exist in a first testing revision of hardware,
Good luck to in your nice compact design :)

BTW - do you have comnnector pins detailed description for Blitzbox 34 pins
Some are clear, some related to WB O2, some to USB

Boost? - how and where connect?
disco? - how and where connect?
LMM - Means MAF ?
IDV - ???
BP - ???
By TR6
#46957
Nice Project!!
Is the assembled hardware available to buy already?
I would like to order one or better two christmas gifts for myself :D
By fram
#47458
Hi Thomas,

Just had a look at your last schematic, very nice project! :)
Fast feedback:
-SOT23 package for MOSFET: i'm a bit worried about reliability with so small package/low rated power FET
-R41 is floating...
-SJ4: replace +UB with +12V
-IC5: MP2359 is obsolete and not recommanded for new design
-IC2: Add VUSB/USB+ on pin 5
-L1: change USB+ with +5V, add diode with USB+ on Anode and +5V on Cathode.
-NCV1124 is a low cost choice for Crank/Cam signal, take care about common mode rejection because no differential input (noise on signal!)
-Take care about max voltage for C12/C14
-No more room on the PCB for IDLE stepper? Not needed?

my 2 cents at the moment ;)
By tooly
#47460
hallo fram,
thanks for your feedback.
this baord is optimized for jlcpcb thats the reason for MP2359 (11050 in stock)
R41 is for solder on R10 on the back if you go with full sequentiell ignition.
there is no space and pins(connector) left for stepper.
User avatar
By PSIG
#47468
fram wrote: Wed Jan 06, 2021 10:12 am -SOT23 package for MOSFET: i'm a bit worried about reliability with so small package/low rated power FET
Indeed, a cool project. 8-) I also agree with Fram's concern over the AO3400A SOT23 MOSFET. My quick napkin calculations for power dissipation indicate a 12-ohm injector at 85%DC, or a typical PWM IAC valve will smoke it sooner than later. Did I mess-up my calc's, or how did you get good numbers?
User avatar
By chaoschris
#47542
This has been my calculations:
calculations_AO3400A.jpg
calculations_AO3400A.jpg (1.36 MiB) Viewed 7293 times
The power dissipation from the datasheet says 0,9W at 70 degrees, so there should be enough safety at 100% DC
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 18

It looks like you have a fuel supply issue. readin[…]

Will this have an updated version about this featu[…]

Vr Conditioner Noise when cranking

I did the fix, but it's not work. I put my setti[…]

Perhaps some different points and pictures. Instr[…]

Still can't find what you're looking for?