COP + speeduino+6cyl

COP + speeduino+6cyl#41668

By Jim_Coupe - Tue Mar 24, 2020 11:25 am

- Tue Mar 24, 2020 11:25 am #41668

Hi, Thinking of running 6cyl COP.. But speeduino outputs 12V not 5V.. Is there any thread around here for examples? dida search found nothing.. Also E-Gas is it support for that?

Re: COP + speeduino+6cyl#41669

By LPG2CV - Tue Mar 24, 2020 12:18 pm

- Tue Mar 24, 2020 12:18 pm #41669

V4 board you can select 5v/12v at jumper 1.

Mere Mortal

Re: COP + speeduino+6cyl#41681

By theonewithin - Wed Mar 25, 2020 1:01 am

- Wed Mar 25, 2020 1:01 am #41681

Ignition outputs are 5/12v selectable. See the wiki for details.

No egas support.

Also Sequential over 4 cylinder is not well supported for either fuel or ignition.

It can be done but is not a simple task and you can have either ignition or injection not both.

There is basically no reason to go sequential in most cases anyway so best to explain what your setup is to be so someone can suggest if it would be of any benefit.

Re: COP + speeduino+6cyl#41703

By PSIG - Wed Mar 25, 2020 9:14 pm

- Wed Mar 25, 2020 9:14 pm #41703

Jim_Coupe wrote: ↑Tue Mar 24, 2020 11:25 am … Also E-Gas is it support for that?

E-gas has multiple meanings. Do you mean ethanol/gasoline blends, or the proposed 'E-gas' natural-gas-based fuels? Ethanol blends (0-100%) and flex-fuel sensors are supported.

David

-= If it was easy, everyone would do it =-

Re: COP + speeduino+6cyl#41717

By runesm - Thu Mar 26, 2020 6:49 am

- Thu Mar 26, 2020 6:49 am #41717

theonewithin wrote: ↑Wed Mar 25, 2020 1:01 am

Also Sequential over 4 cylinder is not well supported for either fuel or ignition.

It's riiiight on the verge of being there though, with 6cyl full seq on the mega.

Re: COP + speeduino+6cyl#44486

By Fran9r - Tue Jul 28, 2020 10:38 pm

- Tue Jul 28, 2020 10:38 pm #44486

Is sequential available as yet or an idea when it will be? I would love that...

Re: COP + speeduino+6cyl#44493

By Fran9r - Wed Jul 29, 2020 10:53 am

- Wed Jul 29, 2020 10:53 am #44493

Could a GIPO STD version 1 or 2 provide the PWM and table to provide the signal to drive a second bank?

Re: COP + speeduino+6cyl#44502

By dazq - Wed Jul 29, 2020 9:08 pm

- Wed Jul 29, 2020 9:08 pm #44502

Fran9r wrote: ↑Wed Jul 29, 2020 10:53 am Could a GIPO STD version 1 or 2 provide the PWM and table to provide the signal to drive a second bank?

No sorry its not suitable for that

Quantum Coupe with V04 on Ford 1.4CVH,Quantum 2+2 with Custom V04 on Jaguar 3.0l AJ30 V6
mini GPIO :done More soon
CANbus broadcast interface: done
Simple sd logger :done
External CAN io: Inputs :done
Gearbox controller: working

Re: COP + speeduino+6cyl#44522

By theonewithin - Thu Jul 30, 2020 10:43 am

- Thu Jul 30, 2020 10:43 am #44522

Nothing much has change on the sequential side of things.

No official hardware supports it.

Still need to do the leg work yourself at this stage.

Software is good for 8X8 now though.