For discussion of anything related to the Speeduino documentation wiki
By rotor
#32468
Honda OBD2A/B connector --104 pin TE 179686-6, Plug A -- 32 pin TE 179681-6, Plug B -- 25 pin TE 179679-6, Plug C -- 31 pin TE 179680-5, Plug D -- 16 pin TE 179678-6

OBD1 Honda Header -- 64 pin TE 174518-7 (same as Mazda)
#34239
Copy/Paste from Andrey's thread-

I've done some digging in this regard. My interest is specifically Toyota, but I believe there is plenty of Japanese crossover. As I can't edit the wiki, I'll put my findings here.

https://www.te.com/commerce/DocumentDel ... 7F172315-7

is an excellent chart for 80s Toyotas. Both of the 18 pin plugs are now obsolete. The 52 pin socket (TE 172319) correlates with Toyota ECUs labeled 10-18-24, such as early 3SGE, 7MGTE and 4AGZE. The 30 pin socket (TE172491) suits ECUs labelled 18-12, specifically the ADM 22RE. The 42 pin socket (TE 172489) suits ECUs labelled 10-18-14, such as early 22R(T)E and 4AGE.


For later (90s) Toyota ECUs, the common connectors are the 64 pin (26-16-22) listed in the wiki, the 54 pin (26-16-12) suits the last 22RE, 4AGE, 4/7AFE, and a 42 pin marked 26-16 (TE 175446-1) which suits the listed 42 pin models, as well as some 22RE and 4AFE ECUs.

Hope this helps someone. Would love to see this info in the wiki. All these connectors have PCB footprints in PDFs on the TE website.
Last edited by vandea05 on Fri Feb 28, 2020 11:06 am, edited 1 time in total.
#34241
Not sure if this is in an earlier post, but here's some info on the golf VR6 coil pack with built in igniters:

Vw part number of coil pack 0031585001. Pins are 3mm wide and i measured them at 5.5mm pitch.

The connector for this coil pack with the rectangular connector (some are oval shaped) is known as a "flat connector" , part number for this is 357972755.

Please note, this is NOT the same as a JPT (junior timer) connector! e.g. Bosch part number 1280703024 is NOT the correct connector for this coil pack. It is too small.
8-)
#51004
Could we please add a new MG Rover sub section to the ecu connectors information?

For early MG / Rover cars using MEMS1.6 / MEMS1.9

This covers early MG / Rover 100, 200, 400, 600 - K and T series variants.

ECU Plugs are:

Econoseal III Wire - 36way.
MEMS1.6 has an optional smaller plug:
Econoseal III - 18way
#65350
I found the ECU connector for the following:
03-06 Toyota Matrix 1ZZ or 2ZZ
03-06 Toyota Corolla 1ZZ or 2ZZ

TE 6376430-2 - In stock at Mouser and Digikey!

Unfortunately the Celica GT-S 2ZZ uses a different connector that I cannot seem to find.
#65374
Lucas@AirLift wrote: Fri Oct 20, 2023 8:10 pm I found the ECU connector for the following:
03-06 Toyota Matrix 1ZZ or 2ZZ
03-06 Toyota Corolla 1ZZ or 2ZZ

TE 6376430-2 - In stock at Mouser and Digikey!

Unfortunately the Celica GT-S 2ZZ uses a different connector that I cannot seem to find.
This should actually be 03-07 for both matrix and corolla. Different years use different pinouts but the connector stays the same

Hi, I am trying to assign Signed values to the x-a[…]

Vr Conditioner Noise when cranking

New version 202305 don't fix the issue. Now after[…]

blitzbox

I've finally figured out why MAP and Lambda weren'[…]

Hello, I bring news!! Let me tell you that after […]

Still can't find what you're looking for?